JC3LE-2P RCBO:6 kA定格および回路選定
二極の RCBO 残存電流波形や故障時の動作を省略しても、注文は一見完全に見えることがあります。JC3LE-2Pの場合、感電や火災を防ぐという大まかな約束よりも、それらの詳細がより重要です。保護機能は回路およびその設置規則に適合している必要があります。.
概要:JC3LE-2PはRCBOであり、過電流保護と 残留電流保護 1つの2極デバイスに搭載されています。公開されている製品情報には、6-63のA特性、B特性、またはC特性、現在の技術表におけるタイプAの残留電流オプション、および6のkA級短絡耐量が記載されています。いずれの値も、信頼する前に正確な注文コードをご確認ください。回路電流、波形、感度、極数、故障レベル、および現地の設置規則から始め、その後、テストボタンと試運転時の点検を文書化してください。.
JC3LE-2P 保護範囲
RCBOは、ラベルだけではなく、保護すべき範囲に応じて選定されます。MCB部は過負荷および短絡に対処し、残留電流部は電流経路を比較して、設定された残留電流値を超えたときに動作します。.
JC3LE-2P 保護機能
公開されたJC3LE-2Pの説明には、二極スイッチング、接点インジケーター、および選択可能なB/Cカーブが記載されています。注文された 残留電流型 接続負荷および現地の規格に適合している必要があります。30 mA、100 mA、または300 mAの感度は設計上の決定事項であり、一般的なRCBOの名称から感電保護や火災防止を推測してはなりません。.
設置境界
中性線を配線図に示された検出経路に接続し、トルク端子を電流指示値に合わせて締め付け、系統側/負荷側の方向を確認してください。所定の計測器を用いて装置を試験し、その結果を記録してください。前面の試験ボタンは、完全な試運転手順の代わりにはなりません。.
The 4極RCBOガイド アラーム信号、負荷電流、および 破壊能力 別途確認が必要です。.
RCBO仕様確認
| 決定次元 | 確認すべきこと | なぜ重要なのか |
|---|---|---|
| 過電流 | 定格電流とB/C曲線 | 導体の許容電流と突入電流が一致する |
| 残留電流 | タイプACまたはタイプA;IΔn | Matches waveform and protection objective |
| 故障時の義務 | Declared breaking capacity | Must exceed prospective fault current |
| 切り替え | Two-pole neutral isolation | Supports the specified isolation method |
Reading the current JC3LE-2P listing
The current W9 product table lists 6 kA at 230/240 V, 50/60 Hz, 6–63 A options, 30/100/300 mA sensitivity and B or C overcurrent curves. Its waveform table identifies Type A. These are separate specification fields: a 6 kA short-circuit rating does not describe residual-current sensitivity, and a B curve does not make the device a Type B RCD.
An order should identify all these fields together. For example, a circuit requiring additional protection cannot adopt a higher residual-current threshold simply to stop unwanted operation. Investigate standing leakage, shared neutrals and connected equipment, then apply the destination rules and manufacturer instructions. Do not use this article as a live-work procedure.
比較の仕方 RCBOおよびRCCBの保護 インテグレート型過電流保護と残留電流検出を区別するのに役立ちます。.
RCBO Application Requirements
| 申請 | Check before release |
|---|---|
| 照明回路およびコンセント回路 | Load current, curve and 30 mA requirement |
| Motor or refrigeration branch | Starting current and nuisance-trip margin |
| 電子機器用負荷 | Residual-current waveform and Type A need |
基準とコンプライアンス
IEC 61009-1 is the product standard for RCBOs; IEC 61008-1 covers RCCBs without integral overcurrent protection. IEC 60364-4-41 addresses protection against electric shock at installation level. A standard reference is not a certificate for every model, so request the exact declaration, test scope and wiring diagram for the supplied device.
選定および試運転チェックリスト
- 記録電圧、電流、ポール数、負荷プロファイル、および将来的な故障電流。.
- 承認された図面と標準仕様に、正確なモデルと付属品を一致させます。.
- レビューの調整、許可の取得、温度および保管環境の確認を行う。.
- 範囲内で宣言書、試験資料、および設置手順書の提出を求めます。.
- 導入時の記録設定、トルク値、機能テスト結果を記録します。.
よくある質問
Is JC3LE-2P a 10 kA RCBO?
The current product table lists 6 kA, not 10 kA. Use the delivered order code and marking to confirm the rating at the actual circuit voltage; do not borrow a rating from a different JC3LE model.
Does the B curve mean Type B residual-current protection?
No. B and C curves describe overcurrent operation, while Type A describes residual-電流波形 capability. Both fields must be specified independently.
Can a 300 mA option replace a required 30 mA device?
Not merely to avoid tripping. Sensitivity must satisfy the circuit’s protection objective and local installation rules; a higher threshold is not an equivalent substitute for required additional protection.
Why does an RCBO trip with its load disconnected?
A shared or incorrectly routed neutral, wiring defect or device problem may remain even when the appliance is removed. A competent electrician should isolate and test the circuit rather than repeatedly reset it.
参考文献
Review the JC3LE-2P information with the current datasheet and contact W9 Group with the circuit schedule, fault level and destination-market requirements.
回路レベルでの選択については、, W9グループへのお問い合わせ 回路図、負荷波形、接地配置、および適用可能な設置規則を考慮して。.





































