ホームブログRCBOの機能は何ですか?

RCBOの機能は何ですか?

公開日時: 2026-06-24

回路の故障が、自動的に全盤停電に至るべきではありません。これがRCBOを仕様化する際の実用的な設計上の課題です。すなわち、個々の回路において、文書化された動作限界を伴う漏電保護および過電流保護を確実に提供できるかどうか、という点です。その答えは、単にMCBと同じDINレールスペースに収まる機器を選ぶだけでは決まりません。.

簡潔な回答:RCBOは、漏電保護機能と過負荷保護機能を兼ね備えています。 短絡保護 規定の定格範囲内で。IEC 61009-1:2024は、家庭用および類似の用途向けRCBOを対象としています;IEC 61008-1に該当するRCCBには、内蔵の過電流保護機能がありません。回路レベルのRCBOを採用することで、残留電流事象の影響を受ける無関係な負荷の数を減らすことができますが、完全な選択性については依然として確認が必要です。定格電流、過電流特性曲線、残留電流の種別および感度、電圧、極数、遮断容量を個別に指定したうえで、配電盤との互換性を確認してください。.

RCBOの保護機能

漏れ電流保護 監視対象の通電導体における不平衡に応答します。過負荷保護は時間経過に伴う過大電流に応じ、短絡保護は機器の定格範囲内の高値の故障電流に対処します。これらの機能はそれぞれ異なる危険に対応し、動作特性も異なります。.

各RCBOの内部機構が同一であると記述してはなりません。過電流検出および残留電流検出の方式は、製品によって異なり得ます。これには、電圧依存型と電圧独立型の残留電流検出方式が含まれます。承認済みの取扱説明書には、電源条件下におけるデバイスの正確な動作特性および必要な接続方法が明記されています。.

保護機能にも限界があります。バランスのとれた線間対地中性点間の故障では、たとえそれが危険な状態であっても、残留電流による不平衡が生じないことがあります。RCBOという用語からは、専用のアーク検知機能を必ずしも意味するものではありません。RCBOは、適切な接地、導体の選定、絶縁、点検、および設置規則で要求される追加措置に代わるものではありません。.

JC3LE four-pole electromagnetic RCBO product image
複合保護であっても、電気的および残留電流に関する仕様は別々に設定する必要があります。.

RCBOとMCBおよび共用RCCBによる保護

個別のRCBOは、あくまで個々の回路の保護を独立して行うものであり、上流側で発生するすべての停電に対応するわけではありません。ある回路に漏電故障が発生した場合、その回路専用の機器が動作することで、下流側の共用グループ全体が動作する必要はありません。ただし、上流側のRCDや過電流保護装置、または電源の異常などによって、他の回路にも影響が及ぶ可能性があります。一つの機器しか動作しないと安易に約束するのではなく、漏電時の協調性と短絡時の選択性の両方を確認してください。.

保護措置をその実際の機能に基づいて比較する
アレンジメント 保護機能 連続性の考慮 設計チェック
MCBのみ 過電流 専用の漏れ検知機能を備えていません。 追加の残留電流に関する要件
回路用MCBと共用のRCCB 漏れ電流保護に加え、別途過電流保護装置を設置 漏洩イベントにより、共有グループが切断される可能性があります。 グループ化、総漏れおよびデバイスの連携
個別のRCBO 各該当回路上の両方の機能 回路レベルの漏れに対する影響を受ける範囲を縮小できる 中立的な分離と上流側の調整
AFDD/RCBOの組み合わせ アーク検出および宣言された複合機能 回路の配置および上流側のデバイスに依存します。 正確な組み合わせの承認および現地の要件

からの区別 RCCB保護 機能性は、単なる物理的特性ではありません。漏電遮断器(RCCB)は、過負荷保護機能を備えていないにもかかわらず、より高い許容電流定格を持つことがあります。一方、漏電・過電流遮断器(RCBO)の公称アンペア定格は、その残留動作感度を示すものではありません。.

RCBO product illustration retained from the original article
製品画像だけでは、EV充電器やその他の特定の負荷への適合性を証明するものではありません。.

RCBOの定格要件

から始める 負荷電流, 導体の許容電流、電圧、および利用可能な短絡電流を考慮し、設計条件と負荷特性に基づいて適切な過電流特性を選定してください。理由の不明なトリップを隠すために異なる動作曲線を設定してはなりません。動作特性の変更は故障保護に影響を及ぼす可能性があるからです。.

次に、漏れ電流の検出感度および波形タイプを特定してください。コンバータ方式の機器では、通常の正弦波交流の漏れ電流を前提とした仕様を超える要件が求められる場合があります。機器の取扱説明書および適用される規則に従い、製品が要求される故障波形を明示的にサポートしていることを確認してください。残留型Bという用語は、過電流特性曲線のB種とは同一ではありません。.

IEC 61009-1:2024の公称範囲には、使用電圧が440 V AC以下、定格電流が125 A以下、短絡容量が25,000 A以下のものが含まれます。これらは標準的な範囲の限界であり、すべてのRCBOがその定格を持つことを示すものではありません。提案されている機器については、実際のデータシートおよび市場向けドキュメントをご請求ください。.

JCR2-63 RCBO product image from the original article
承認前に、正確なJCR2-63のバリアントおよび申請書類を確認してください。.

RCBOの中性線経路

各RCBOの監視対象導体は、それぞれの認可された配線方式に従わなければなりません。中性線の借用や中性バーの誤接続、意図しない中性線と大地との接続は、設計上の電流バランスを損ない、誤動作を引き起こす可能性があります。系統側および負荷側の配線方向、中性線の切り替え機能、および機能接地線については、必ず指示書に記載された通りに確認してください。極数から推測して判断してはなりません。.

したがって、改造は単なる取手の交換にとどまりません。バスバー系統、端子の位置合わせ、ケーブル容量、筐体内部のスペース、および組み立てメーカーが許可する組み合わせを確認してください。 RCD機能ガイド 残留電流のバランスに関する背景情報を提供していますが、その接続方法を明確に定義しているのは、選定されたRCBOの仕様書のみです。.

試運転および故障調査の範囲
観察 調査が必要な可能性のある問題 有資格者による確認 避けるべき危険な近道
ボードの改修後の旅行 中性線の接続ミスまたは誤った接続 回路の識別と中性線の分離 Bypassing the residual-current function
Trip only when several loads operate Load overload or aggregate leakage on that circuit Identify the indicated function and measure the relevant condition Assuming all trips have the same cause
Trip during equipment starting Inrush, leakage transient or another fault Load profile and model-specific characteristic Changing curve or sensitivity without a design review
Test button does not operate as instructed Supply, wiring or device issue Isolate and assess using the approved procedure Leaving a suspected defective device in service

RCBO Trip Indication

Some devices distinguish residual-current trips from overcurrent trips; others provide less information. Record the indication before resetting, together with the operating load and time. A position indicator or event display is a lead for diagnosis, not a complete finding about the cable or appliance.

Testing should follow the device instructions and the installation’s commissioning requirements. A push-button check does not verify every protective conductor, termination or disconnection condition. SafeWork NSW’s workplace guidance separates competent testing records from push-button tests; its jurisdiction-specific requirements should not be copied as a universal maintenance schedule.

  1. Define the circuit and applicable protection requirements.
  2. Select overcurrent and residual-current characteristics separately.
  3. Approve the device/board combination and wiring arrangement.
  4. Test and document the completed installation.
  5. Hand over the indication, test and escalation instructions.

For procurement, W9 Group’s RCBO range is a starting point for model selection. Confirm the requested configuration and its documentation; do not extend a category description into an assertion that every listed product suits EV charging, converter loads or every national installation rule.

よくある質問

What is the function of an RCBO?

It combines residual-current protection with overload and short-circuit protection within its declared ratings. The correct combination must still be selected for the circuit and board.

What is the difference between an RCBO and an RCCB?

An RCCB lacks integral overcurrent protection, while an RCBO incorporates it. The 残留電流型 and sensitivity still need checking for both.

Will an RCBO stop the whole building from losing power?

It can reduce the number of circuits lost for a circuit-level leakage fault, but it does not guarantee complete upstream selectivity or prevent supply outages. Evaluate the whole protective arrangement.

Does Type B mean the same thing as curve B?

No. Residual-current Type B refers to a waveform-detection category; a B overcurrent curve concerns overcurrent operation. The specification must identify which characteristic is being requested.

Can any RCBO replace an MCB in the same space?

No. Check electrical duty, neutral routing, busbar and terminal interfaces, and assembly approval. Module width alone does not prove compatibility.

参考文献と結論

References were accessed on 14 October 2026. Combined protection still requires a complete circuit specification. Contact W9 Group with the duty, residual-current requirements and destination market for documented model selection.

回路レベルでの選択については、, W9グループへのお問い合わせ 回路図、負荷波形、接地配置、および適用可能な設置規則を考慮して。.